Elgin Pelican P Specifications download pdf (Page 88)

Other Conveyor Adjustments

LOWER ROLL SCRAPER

ADJUSTMENT

Lower roll scraper adjustment should be checked

periodically and whenever the belt is removed. The

square opening just above the lower roll bearing

(Figure SP-18) provides access for adjustment. To

adjust the scraper, take the following steps.

1. Loosen two nuts at each end of the scraper.

2. Adjust the scraper to clear the roll by no more

than 1/16 inch (1.6 mm).

3. Tighten the nuts.

NOTICE

The condition of the lower belt scraper (rubber) that

is part of the lower roll scraper assembly should be

checked, and the belt scraper should be replaced, if

necessary.

SERVICE

PROCEDURES

SP-22

ROLL SCRAPER

Right Side Of Lower Roll

Figure SP-18

1 2 ... 83 84 85 86 87 88 89 90 91 92 93 ... 111 112

Pelican® P 1
SERIES P 3
The Elgin Pelican 5
Table of Contents 9
Adjustment.............SP-27 10
SAFETY INFORMATION 11
CALIFORNIA PROPOSITION 65 12
FOLLOW SAFETY 12
INSTRUCTIONS 12
WEAR APPROPRIATE 13
CLOTHING/PROTECTION 13
DRIVING THE SWEEPER 13
HANDLE FUEL SAFELY — 13
AVOID FIRES 13
AVOID CONTACT WITH 14
MOVING PARTS 14
AVOID MACHINE INSTABILITY 14
PARK SWEEPER SAFELY 14
AVOID OVERLOADS 15
AVOID ELECTRICAL POWER 15
PRACTICE SAFE 15
MAINTENANCE/REPAIRS 15
PREVENT BATTERY 16
EXPLOSIONS 16
AVOID OVERLOADING 16
ELECTRICAL SYSTEM 16
AVOID HIGH PRESSURE 17
USE PROPER TOOLS 17
TIRES AND RIMS 18
OBSERVE ENVIRONMENTAL 18
PROTECTION REGULATIONS 18
Maintenance Chart 20
RH cover 20
Lubricate sprung guide wheel 21
DESCRIPTION 23
PRINCIPLES OF OPERATION 24
CONVEYOR 25
CONTROLS 27
DRIVE WHEELS 27
GUIDE WHEEL 28
GENERAL DATA 29
Series P 31
OPERATION 33
Sweep Controls 34
Right Side 34
Left Side 34
OPERATING CHECKLIST 38
Before Starting Engine 38
After Starting Engine 39
STARTING THE ENGINE 40
COLD WEATHER STARTING 41
TRANSPORT 42
SWEEPING 44
SPRAY WATER 46
SWEEPING PATTERNS 48
REVERSING THE CONVEYOR 50
DUMPING THE HOPPER 51
Hopper Dump Control 52
Figure O-10 52
SHUTTING DOWN THE UNIT 53
AT END OF SHIFT 53
MAINTENANCE 55
Figure M-1 58
Figure M-2 59
DAILY WASHDOWN 61
BUBBLE WINDOW 63
LUBRICATION 64
Oil Fill Level and Volume 65
SERVICE PROCEDURES 67
AIR CLEANER 69
FUEL SYSTEM 71
DRAINING FUEL WATER 71
SEPARATOR 71
CHANGING FUEL FILTER 73
BLEEDING FUEL SYSTEM 74
HYDRAULIC SYSTEM 74
SPRAY WATER SYSTEM 75
BROOM ADJUSTMENT 76
SIDE BROOM ADJUSTMENT 77
Side-To-Side Angle 77
Front-To-Back Angle 77
Down Pressure 78
MAIN BROOM ADJUSTMENT 79
Standard (Chain) Suspension 79
Hydraulic Suspension 79
DIRT SHOE ADJUSTMENT 80
DIRT DEFLECTORS 81
CONVEYOR ACCESS 82
ADJUSTING CONVEYOR 84
Conveyor Belt Adjustments 84
BELT TENSION 85
BELT ALIGNMENT 86
Other Conveyor Adjustments 88
CONVEYOR GROUND CLEARANCE 89
STOP BOLT LIFT CYLINDER 90
REPLACING CONVEYOR BELT 91
Removing Conveyor Belt 91
Squaring Conveyor Structure 92
Lower Roll Offset Adjustment 93
Installing Conveyor Belt 94
SPLICING CONVEYOR BELT 95
REVERSING CONVEYOR 96
Belt Repairs 97
Figure SP-25 97
MAIN BROOM REPLACEMENT 98
CAB AIR FILTER 100
WHEELS AND TIRES 100
WINTER STORAGE 100
SPRING STARTUP 102
PROCEDURES 104
TROUBLESHOOTING 105
SHOOTING 107
TROUBLE 107
GLOSSARY 109
Elgin Sweeper Company 112
1300 W. Bartlett Rd 112
Elgin, IL 60120 112
847-741-5370 112

Comments to this Manuals

No comments

Elgin Pelican P Specifications Page 88

Comments to this Manuals